Stovax Chamonix & Aspen (P)8135**UC User Manual

Aspen, Chamonix & TahoeDecorative Gas Basket FiresWith upgradeable control valveInstructions for Use,Installation and ServicingFor use in GB, IE (

10USER INSTRUCTIONS7.8.5 Place one large log (No. 6) so that it rests on top of the rearand front logs to the LH side. Place the other large log (No.

11USER INSTRUCTIONS7.9.6 Place the two thin logs (No. 12), one at each side sitting onthe tray and resting against the previously positioned logs.Pla

MODEL GAS GAS INLET AERATION INJECTION BURNER INPUT GAS FLOW RATETYPE CATEGORY PRESSURE SIZE SIZEPRESSURE(mb)(pre-set)(kW) (m3/hr)(mb) HIGH LOW HIGH

13INSTALLATION INSTRUCTIONSSITE REQUIREMENTS1.1 The chimney or flue system must comply with the rules inforce.1.2 Fireplace opening up to 450mm (18&qu

144.1 This appliance must stand on a non-combustible hearth thatis at least 12mm thick.4.2 It must be fitted into a non-combustible opening.4.3 These

15IMPORTANT:ENSURE THAT THE APPLIANCE ISCORRECTLY ADJUSTED FOR THE GAS TYPE ANDCATEGORY APPLICABLE IN THE COUNTRY OF USE.REFER TO DATABADGE AND TECHNI

164.1 Your fire is fitted with a control valve that can be easilyupgraded to battery powered remote control. This upgradecan be fitted by anyone capab

5.4.3 Starting at the front, place 14 alternating large and smallcoals or pebbles around the perimeter of the fire, theyshould sit on the bottom row o

185.5.2 Place 18 small coals or pebbles around the edge of the trayas shown, ensure that there are gaps between each coal orpebble. Place one on top o

195.6.4 Place the remaining 4 large coals or pebbles on top of thesquare blocks, ensure that they lean against the centralsmall coal or pebble and th

2CONTENTSPAGEAPPLIANCE COMMISIONING CHECKLIST 3USER INSTRUCTIONS 4INSTALLATION INSTRUCTIONS 12Technical Specifications 12Site Requirements 13Installat

20INSTALLATION INSTRUCTIONSINSTALLATIONIt may be necessary to make small changes to the logpositioning in order to achieve the most pleasing flameeffe

21INSTALLATION INSTRUCTIONSINSTALLATIONIt may be necessary to make small changes to the logpositioning in order to achieve the most pleasing flameeffe

22INSTALLATION INSTRUCTIONSCOMMISSIONING6.1 Close all windows and doors to the room, check allcontrols, and allow fire to burn on maximum for 5 minute

23SERVICING INSTRUCTIONSSERVICING / FAULT FINDING CHARTSThis appliance must be serviced at least once a year by acompetent person.All tests must be se

24SERVICING INSTRUCTIONSFAULT FINDING CHARTSIGNITION FUNCTIONAL CHECK 2NO SPARKEnsure there is no debris around the pilot assembly, (e.g. coal, soot e

25SERVICING INSTRUCTIONSFAULT FINDING CHARTSPILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USEEnsure there is no debris around the pilot assembly, (e.g.

262.3 To release the right hand side of the control cover insert anarrow blade screwdriver into the slot shown in diagram 3,lever it gently and pull f

272.5 replace with a new ignition lead following the same route asthe old one. replace the valve cover and securing screw.2.6 check the operation of t

285.1 Remove the thermocouple from the back of the controlvalve. See diagram 8 arrow B.5.2 Undo the mag unit retaining nut. See diagram 8, arrow C5.3

298.1 Remove the fire, refer to section 1.8.2 Disconnect the 2x8mm and 1x4mm gas pipe fittings at theback of the gas valve, arrow A and disconnect the

3FLUE CHECK PASS FAIL1. Flue is correct for appliance2. Flue flow test3. Spillage testGAS CHECK1. Gas soundness & let by test2. Standing pressure

30COMMON COMPONENTSControl Valve GC0096Ignition lead GC0090Magnetic Unit GC0092Control Cover GC0087Upgrade Kit 8455Pilot Shield (Standard) GZ1368Pilo

31SERVICE RECORDS1ST SERVICEDate of Service:...Next Service Due:...

Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JGTel: (01392) 261999 Fax: (01392) 444148 E-mail: [email protected]

4USER INSTRUCTIONS1.1 Installation and servicing must only be carried out by a competent person.1.2 In all correspondence, please quote the appliance

55.1 Your fire is fitted with a control valve that can be easilyupgraded to battery powered remote control. This upgradecan be fitted by anyone capabl

67.3.3 Using the small beads, fill the fire to the top. See diagram 3.7.3.4 Smooth out the fire beads, it is important to ensure that thefire is compl

77.5.1 Place 15 large square blocks in a solid mass in the centre ofthe burner tray as shown, ensure they fit tightly together.See diagram 9.7.5.2 Pla

8USER INSTRUCTIONS7.6.3 Place one large coal or pebble on top of the pilot shield,then place 10 alternating large and small coals or pebblesaround th

7.7.4 Place log (No. 7) along the LH side of the tray, log (No. 9)along the RH side of the tray and place logs (No. 8 and 11)along the front of the t