LineaBalanced Flue Convector FireInstructions for Use,Installation and ServicingFor use in GB, IE (Great Britain and Eire)PR0731 Issue 8 (September 20
10TIMBER FRAMED BUILDINGS1.5 It will be necessary to provide additional clearance whenthe flue passes through a wall containing any combustiblemateria
11INSTALLATION INSTRUCTIONSSITE REQUIREMENTS4.4 All combustible materials must be removed from behind theappliance. See diagram 6.4.5 The Linea may be
12IMPORTANT: BEFORE THE APPLIANCE CAN BEOPERATED THE REMOTE HANDSET MUST BE TUNED TOTHE CONTROL BOX SITUATED UNDER THE APPLIANCE.IF THIS PROCEDURE IS
2.7 The flue can now be cut to size. Measure the thickness ofthe wall, then deduct 12mm. This is the length requiredwhen measuring from the line on th
3.1.3 The remote handset must now be programmed. Push the ON /OFF button (11), the ON or OFF display will start flashing. Thenpress the ON / OFF butto
15IGNITION FUNCTIONAL CHECK 1PILOT WILL NOT LIGHTEnsure there is no debris around the pilot assembly, (e.g. soot, etc.) which could short the spark, c
16PILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USEEnsure there is no debris around the pilot assembly, (e.g. soot etc.) Check for fluff in the pilot ae
172.4 Raise the burner from the slot in the bracket, pull theburner forward and slide to the left to clear the injector.Take care not to lose the spri
184.7 Reassemble in reverse order and replace the pilot gasketwith a new one.4.8 Check for gas leaks.5.1 To gain access to the pilot pipe, it is easie
197.2 Disconnect the thermocouple from the gas valve. Seediagram 8 arrow C.7.3 Undo the thermocouple nut in the back of the pilot burnerby half a turn
2CONTENTSCOVERING THE FOLLOWING MODELS8651 P8651PAGEAPPLIANCE COMMISSIONING CHECKLIST 3USER INSTRUCTIONS 4INSTALLATION INSTRUCTIONS 8Technical Specif
10.3 Remove the main burner as described in section 2.10.4 Remove the locknut from the injector. See diagram 15.10.5 Remove the feed pipe from the gas
21SERVICING INSTRUCTIONSREPLACING PARTS11.1 Remove the lower cover. See diagram 6.11.2 Locate the control box and remove all of the wiresconnected to
22SERVICING INSTRUCTIONSREPLACING PARTSIn order to change between gas types it will be necessary tochange the following items.Main InjectorMain Burner
23SERVICING INSTRUCTIONSREPLACING PARTS15. SHORT SPARES LISTComponent NG LPGPROPANE BUTANEBURNER UNIT GC0104 GC0105 GC0106MAIN INJECTOR IN0053 IN0052P
24SERVICE RECORDS1ST SERVICEDate of Service:...Next Service Due:...
Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JGTel: (01392) 261999 Fax: (01392) 444148 E-mail: [email protected]
3FLUE CHECK PASS FAIL1. Flue is correct for appliance2. Flue flow test N/A3. Spillage test N/AGAS CHECK1. Gas soundness & let by test2. Standing p
4USER INSTRUCTIONS1.1 A competent person must carry out installation andservicing.1.2 In all correspondence, please quote the appliance type andserial
52.5 To set the room temperature2.5.1 Following on from section 2.4, once the room temperatureis flashing on the display, it can be set.2.5.2 Press ei
4.1 This is a safety feature incorporated on this appliance whichautomatically switches off the gas supply if the pilot goesout and fails to heat the
7USER INSTRUCTION10.1 If the Linea is fitted with a Designio front, access to thebatteries can be achieved by simply dropping the lowerfront access co
8INSTALLATION INSTRUCTIONSTECHNICAL SPECIFICATIONCOVERING THE FOLLOWING MODELS8651 P8651Efficiency Class IFlue Outlet Size 100 Ø / 152mm ØGas Inlet Co
9INSTALLATION INSTRUCTIONSSITE REQUIREMENTSNOTE: This appliance can only be installed in conjunctionwith the flue supplied.1.1 The flue must be sited
Comments to this Manuals